欢迎访问惠州市欧亚涂料有限公司官网!

设为首页 客户反馈销售服务

欧亚服务热线

0752-2618999

产品中心

products center

contact us

欧亚服务热线//0752-2618996

地址: 惠州市仲恺高新区惠环
街道西坑工业区
电话: 0752-2618999
0752-2618996
传真: 0752-2618995
网站: www.
邮箱: ye168@eurasia.net.cn
3C家电涂料
您当前所在:网站首页>产品中心>3C家电涂料

产品参数 //

产品名称:EUK抗污涂料

产品价格:面议

产品规格:4L,20L

产品数量:现货

所属类别:3C家电涂料篇

生产厂商:惠州市欧亚涂料有限公司

产品详情 //



产品性能测试:

Product performance test:

测试项目
TEST ITEM

测试方法
TEST CONDITION


测试结果
TEST RESULT


附着性
Crosshatch adhesion

1mm^2方格100个,透明胶带测试
A grid of 100 squares (1mm2), peeled with a pressure sensitive tape.

100/100

铅笔硬度

Pencil hardness


三菱2H铅笔500g

MITSUBISHI 2H 500gf


OK


耐磨性

Abrasion resistance


RCA测试法175gf

RCA 175gf


300次无露底

300 time No visible substrate beneath the coating


震动耐磨

Vibration and abrasion resistance


2小时

2hours


OK


记号笔测试

Marking pen test


真彩记号笔划5个位置长35mm左右墨条,观察油墨收缩状况和样板对比

Draw line with length about 35mm by true color marking pen at five positions, observe printing ink contraction and compare it with the sample


OK

耐醇性

Alcohol resistance


995% alcohol, W=9.8N1kgfRubbing for 50 time.

99.5%酒精W=9.8N1kgf)来回擦拭,露底前回数。



≥100回
≥100 time


耐湿热

Humidity resistance


40℃x 98%RH x 48H


无异状
No change

耐高低温循环性

Heat-and-Cold cycle


(-20℃x8h >> 60℃x8h ) x 10 循环

(-20℃x8h >> 60℃x8h ) x 10 cycle


无异状
No change

耐高温

High temperature test



85℃x85RH x 48h




无异状
No change

耐低温

Low temperature test


-25℃x96h


无异状
No change

接触角测试

Contact angle test


a)接触角测量仪;
a) Contact angle meter
b)容量为0.1ml的针管,滴水针头内径0.2mm;
b) Needle tubing with volume of 0.1ml and the pinhead with inner diameter of 0.2mm;
c)测试液体:蒸馏水、正十六烷;(测试水滴为针头外径的2~3倍)
c) Test liquid: distilled water, n-hexadecane (test water drop is 2 to 3 times as large as outer diameter of pinhead)

水滴角≧110度;
油滴角≧65度
Angle of water drop ≧ 110°;
Angle of oil drop ≧ 65°


测试条件:
Preparation of test panels:
1.喷涂底材:ABS塑胶板
1. Substrate: ABS plastic plates
2.前处理:用清洁剂擦拭面油污及尘粒
2. Surface pretreatment: Removing grease and dust, with detergent.
3.漆膜厚度:20~25um (空气喷涂)
3. Film thickness: 20~25μm(air spray coating).
4.预干燥:60℃ X 5min+UV800~1000mg/cm2
4. Pre-drying: 60℃ X 5min+UV800~1000mg/cm2
注意事项:
Notes:
1、涂料应密封贮存于阴凉处,防水、防晒、防高温、远离火源。
1. Sealed and stored in the dry and cool environment. Kept away from water , sunshine, high-temperature and fire.
2、涂料在室温下不开罐的贮存期为半年。
2. Storage period of coating is half a year in room temperature under tank sealing condition.
3、底漆在各自工艺条件下完全固化后方可使用该涂料。依据不同的底漆或基材附著不好的现象可能发生,使用前请确认。
3. The primer must be cured thoroughly before application of UV coatings, otherwise the poor adhesion may occur.
4、使用前请用400目的滤网过滤。
4. Filtered with 400# silk gauze before use.
5、涂料光固化前要有足够的温度和时间预烘干,否则会影响到漆膜性能。
5. The UV coatings must have enough pre-drying before UV curing, otherwise the film properties may be influenced.

版权所有©2016 惠州市欧亚涂料有限公司
地址:惠州市仲恺高新区惠环街道西坑工业区    技术支持:
电话:0752-2618999 2618996 传真:0752-2618995

友情链接:    三分彩票   天天彩票   豪胜彩票app   网上购彩开户   手机彩票网